SpeedTek

SpeedTek RC Un-Cure™ CA Debonder (1 oz.) by BSI

SpeedTek RC UN-CURE™ debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of SpeedTek RC UN-CURE™ will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water. Since cured CA is essentially acrylic plastic, anything that will dissolve CA will also soften most plastics. Care must be used, therefore, when using SpeedTek RC Un-Cure on plastics. Separating plastics parts with a razor saw is usually the best option.

Directions:

SpeedTek RC Un-Cure™ will soften cured super glue (aka cyanoacrylate, CA). To release bonded skin (not near the eyes) apply SpeedTek RC Un-Cure™, then use a small, rounded object like a paperclip to separate the skin with a peeling action, applying more SpeedTek RC Un-Cure™ as needed until the skin areas are debonded. Wash the area with soap and water. The natural shedding of the skin’s outer layer will remove any residual CA within 12 hr. For removing CA from hard surfaces, soak a cloth or paper towel in SpeedTek RC Un-Cure™ and rub areas vigorously. SpeedTek RC Un-Cure™, however, will mar most plastics.

Includes:

1 x SpeedTek RC Un-Cure™ CA Debonder (1 oz.) by BSI

SpeedTek RC Ultra-Cure™ Tire Glue (3/4 oz.) by BSI

SpeedTek RC Ultra-Cure™ is a very high performance clear cyanoacrylate that has a viscosity (thickness) in-between that of Insta-Cure Super Thin and Insta-Cure+ Gap Filling Medium. It is ideal for the mounting of rubber tires onto R/C car wheels.  ULTRA-CURE™ can be used in many other applications that require a slightly thicker thin CA and will bond virtually everything. It is not foam-safe, however.

Directions:

Unscrew top from nozzle. For finer applications, use the extender tip. Carefully lift the sidewall of the tire after it is mounted to the wheel to expose the area to be bonded. Apply a drop of SpeedTek RC Ultra-Cure™CA Tire Glue into the gap, then slowly return the tire to its seated position. Continue this process around the circumference of the tire. Repeat these steps for the other side. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life when not in use. SpeedTek RC Ultra-Cure™ is also superior for bonding most other materials. Soak extender tip in acetone for cleaning.

Includes:

1 x SpeedTek RC Ultra-Cure™ Tire Glue(3/4 oz.) by BSI

SpeedTek RC Stainless Steel Metal Shielded Ceramic Bearing Kit for the Yokomo YD-2Z KIT

Features:

Steel, Ceramic, Metal Sealed bearings are specially designed for any application seeking a high precision, free spinning bearing. These are the true secret weapon for serious rc racers and long distance casters. ABEC 7 tolerances makes the Metal Seal line the closest precision tolerance that SpeedTek RC has to offer.  The Grade 5 ceramic Si3N4 balls will allow the bearing to be lighter and spin 50% faster than a traditional steel bearing.

Specifications:

Bearing Material: Stainless Steel 440C, Ball Material: Ceramic SI3N4, ABEC#7/ISOP4Enclosure: Two Seals, Enclosure Material: Metal SealRetainer Material: Stainless Steel, Radial Play: C0, Lubrication: Oil
(4)     4x8x3   Ceramic
(10)   5x10x4   Ceramic
(4)     10x15x4   Ceramic

NOTE: PHOTOS ARE FOR IDENTIFICATION ONLY
Photos are for Seal / Shield / Bearing Style identification only and ARE NOT a photo of the exact bearing being ordered. Please reference the size.

Includes:
1 x SpeedTek RC Stainless Steel Metal Shielded Ceramic Bearing Kit for the Yokomo YD-2Z KIT

SpeedTek RC Stainless Steel Metal Shielded 8x19x6 Ceramic Bearing (1)

Features:
Steel, Stainless Steel 440C Sealed bearings are specially designed for any application seeking a high precision, free spinning bearing. These are the true secret weapon for serious rc racers and long distance casters. ABEC 7 tolerances makes the Stainless Steel 440C line one of the closest precision tolerance that SpeedTek RC has to offer.

Specifications:
Inside Diameter: 8mm / Outside Diameter: 19mm / Width: 6mm
Bearing Material: Stainless Steel 440C, Ball Material: Stainless Steel 440C
Enclosure: Two Seals, Enclosure Material: Stainless Steel 440C
Retainer Material: Stainless Steel, Radial Play: C0, Lubrication: Oil

Includes:
1 x SpeedTek RC Stainless Steel Metal Shielded 8x19x6 Ceramic Bearing (1)

SpeedTek RC Stainless Steel Metal Shielded 8x12x3.5 Ceramic Bearing (1)

Features:
Steel, Stainless Steel 440C Sealed bearings are specially designed for any application seeking a high precision, free spinning bearing. These are the true secret weapon for serious rc racers and long distance casters. ABEC 7 tolerances makes the Stainless Steel 440C line one of the closest precision tolerance that SpeedTek RC has to offer.

Specifications:
Inside Diameter: 8mm / Outside Diameter: 12mm / Width: 3.5mm
Bearing Material: Stainless Steel 440C, Ball Material: Stainless Steel 440C
Enclosure: Two Seals, Enclosure Material: Stainless Steel 440C
Retainer Material: Stainless Steel, Radial Play: C0, Lubrication: Oil

Includes:
1 x SpeedTek RC Stainless Steel Metal Shielded 8x12x3.5 Ceramic Bearing (1)

SpeedTek RC Stainless Steel Metal Shielded 6x10x3 Ceramic Bearing (1)

Features:
Steel, Stainless Steel 440C Sealed bearings are specially designed for any application seeking a high precision, free spinning bearing. These are the true secret weapon for serious rc racers. ABEC 7 tolerances makes the Stainless Steel 440C line one of the closest precision tolerance that SpeedTek RC has to offer.

Specifications:
Inside Diameter: 6mm / Outside Diameter: 10mm / Width: 3mm
Bearing Material: Stainless Steel 440C, Ball Material: Stainless Steel 440C
Enclosure: Two Seals, Enclosure Material: Stainless Steel 440C
Retainer Material: Stainless Steel, Radial Play: C0, Lubrication: Oil

Includes:
1 x SpeedTek RC Stainless Steel Metal Shielded 6x10x3 Ceramic Bearing (1)

SpeedTek RC Stainless Steel Metal Shielded 5x13x4 Ceramic Bearing (1)

Features:
Steel, Stainless Steel 440C Sealed bearings are specially designed for any application seeking a high precision, free spinning bearing. These are the true secret weapon for serious rc racers. ABEC 7 tolerances makes the Stainless Steel 440C line one of the closest precision tolerance that SpeedTek RC has to offer.

Specifications:
Inside Diameter: 5mm / Outside Diameter: 13mm / Width: 4mm
Bearing Material: Stainless Steel 440C, Ball Material: Stainless Steel 440C
Enclosure: Two Seals, Enclosure Material: Stainless Steel 440C
Retainer Material: Stainless Steel, Radial Play: C0, Lubrication: Oil

Includes:
1 x SpeedTek RC Stainless Steel Metal Shielded 5x13x4 Ceramic Bearing (1)

SpeedTek RC Stainless Steel Metal Shielded  4x8x3 Ceramic Bearing (1)

Features:
Steel, Stainless Steel 440C Sealed bearings are specially designed for any application seeking a high precision, free spinning bearing. These are the true secret weapon for serious rc racers. ABEC 7 tolerances makes the Stainless Steel 440C line one of the closest precision tolerance that SpeedTek RC has to offer.

Specifications:
Inside Diameter: 4mm / Outside Diameter: 8mm / Width: 3mm
Bearing Material: Stainless Steel 440C, Ball Material: Stainless Steel 440C
Enclosure: Two Seals, Enclosure Material: Stainless Steel 440C
Retainer Material: Stainless Steel, Radial Play: C0, Lubrication: Oil

Includes:
1 x SpeedTek RC Stainless Steel Metal Shielded 4x8x3 Ceramic Bearing (1)

SpeedTek RC Stainless Steel Metal Shielded  4x10x4 Ceramic Bearing (1)

Features:
Steel, Stainless Steel 440C Sealed bearings are specially designed for any application seeking a high precision, free spinning bearing. These are the true secret weapon for serious rc racers. ABEC 7 tolerances makes the Stainless Steel 440C line one of the closest precision tolerance that SpeedTek RC has to offer.

Specifications:
Inside Diameter: 4mm / Outside Diameter: 10mm / Width: 4mm
Bearing Material: Stainless Steel 440C, Ball Material: Stainless Steel 440C
Enclosure: Two Seals, Enclosure Material: Stainless Steel 440C
Retainer Material: Stainless Steel, Radial Play: C0, Lubrication: Oil

Includes:
1 x SpeedTek RC Stainless Steel Metal Shielded 4x10x4 Ceramic Bearing (1)

SpeedTek RC Stainless Steel Metal Shielded  3x6x2.5 Ceramic Bearing (1)

Features:
Steel, Stainless Steel 440C Sealed bearings are specially designed for any application seeking a high precision, free spinning bearing. These are the true secret weapon for serious rc racers. ABEC 7 tolerances makes the Stainless Steel 440C line one of the closest precision tolerance that SpeedTek RC has to offer.

Specifications:
Inside Diameter: 3mm / Outside Diameter: 6mm / Width: 2.5mm
Bearing Material: Stainless Steel 440C, Ball Material: Stainless Steel 440C
Enclosure: Two Seals, Enclosure Material: Stainless Steel 440C
Retainer Material: Stainless Steel, Radial Play: C0, Lubrication: Oil

Includes:
1 x SpeedTek RC Stainless Steel Metal Shielded 3x6x2.5 Ceramic Bearing (1)

SpeedTek RC Stainless Steel Hybrid Shielded 6x12x4 Ceramic Bearing (1)

Features:
Steel, Ceramic Hybrid, Orange Sealed bearings are specially designed for any application seeking a high precision, free spinning bearing. These are the true secret weapon for serious rc racers. ABEC 7 tolerances makes the Orange Seal line the closest precision tolerance that SpeedTek RC has to offer. The removable, non-contact rubber seals results in a bearing with less drag and that requires less maintenance than a typical shielded bearing. The Grade 5 ceramic Si3N4 balls will allow the bearing to be lighter and spin 50% faster than a traditional steel bearing. LD = Lube Dry Bearings have been clean and are free of all grease and Oils.

Specifications:
Inside Diameter: 6mm / Outside Diameter: 12mm / Width: 4mm
Bearing Material: Stainless Steel 440C, Ball Material: Ceramic SI3N4, ABEC#7/ISOP4
Enclosure: Two Seals, Enclosure Material: Rubber Seal
Retainer Material: Stainless Steel, Radial Play: C0, Lubrication: LD Dry Lube

Includes:
(1) SpeedTek RC Stainless Steel Hybrid Shielded 6x12x4 Ceramic Bearing

SpeedTek RC Stainless Steel Hybrid Shielded 5x13x4 Ceramic Bearing (1)

Features:
Steel, Ceramic Hybrid, Orange Sealed bearings are specially designed for any application seeking a high precision, free spinning bearing. These are the true secret weapon for serious rc racers. ABEC 7 tolerances makes the Orange Seal line the closest precision tolerance that SpeedTek RC has to offer. The removable, non-contact rubber seals results in a bearing with less drag and that requires less maintenance than a typical shielded bearing. The Grade 5 ceramic Si3N4 balls will allow the bearing to be lighter and spin 50% faster than a traditional steel bearing. LD = Lube Dry Bearings have been clean and are free of all grease and Oils.

Specifications:
Inside Diameter: 5mm / Outside Diameter: 13mm / Width: 4mm
Bearing Material: Stainless Steel 440C, Ball Material: Ceramic SI3N4, ABEC#7/ISOP4
Enclosure: Two Seals, Enclosure Material: Rubber Seal
Retainer Material: Stainless Steel, Radial Play: C0, Lubrication: LD Dry Lube

Includes:
(1) SpeedTek RC Stainless Steel Hybrid Shielded 5x13x4 Ceramic Bearing

SpeedTek RC Stainless Steel Hybrid Shielded Ceramic Bearing Kit for the Traxxas Summit

Features:
Steel, Ceramic Hybrid, Orange Sealed bearings are specially designed for any application seeking a high precision, free spinning bearing. These are the true secret weapon for serious rc racers. ABEC 7 tolerances makes the Orange Seal line the closest precision tolerance that SpeedTek RC has to offer. The removable, non-contact rubber seals results in a bearing with less drag and that requires less maintenance than a typical shielded bearing. The Grade 5 ceramic Si3N4 balls will allow the bearing to be lighter and spin 50% faster than a traditional steel bearing. LD = Lube Dry Bearings have been clean and are free of all grease and Oils.

Specifications:
Bearing Material: Stainless Steel 440C, Ball Material: Ceramic SI3N4, ABEC#7/ISOP4
Enclosure: Two Seals, Enclosure Material: Rubber Seal
Retainer Material: Stainless Steel, Radial Play: C0, Lubrication: LD Dry Lube
(5)      5X8X2.5 Ceramic
(16)     5X11X4 Ceramic
(12)     6X12X4 Ceramic
(4)     6X13X5 Ceramic
(2)     8X16X5 Ceramic
(4)     12X18X4 Ceramic
(2)     20x27x4 Ceramic

NOTE: PHOTOS ARE FOR IDENTIFICATION ONLY
Photos are for Seal / Shield / Bearing Style identification only and ARE NOT a photo of the exact bearing being ordered. Please reference the size.

Includes:
1 x SpeedTek RC Stainless Steel Hybrid Shielded Ceramic Bearing Kit for the Traxxas Summit

SpeedTek RC Stainless Steel Hybrid Shielded Ceramic Bearing Kit for the E-Revo 2.0

Features:
Steel, Ceramic Hybrid, Orange Sealed bearings are specially designed for any application seeking a high precision, free spinning bearing. These are the true secret weapon for serious rc racers. ABEC 7 tolerances makes the Orange Seal line the closest precision tolerance that SpeedTek RC has to offer. The removable, non-contact rubber seals results in a bearing with less drag and that requires less maintenance than a typical shielded bearing. The Grade 5 ceramic Si3N4 balls will allow the bearing to be lighter and spin 50% faster than a traditional steel bearing. LD = Lube Dry Bearings have been clean and are free of all grease and Oils.

Specifications:
Bearing Material: Stainless Steel 440C, Ball Material: Ceramic SI3N4, ABEC#7/ISOP4
Enclosure: Two Seals, Enclosure Material: Rubber Seal
Retainer Material: Stainless Steel, Radial Play: C0, Lubrication: LD Dry Lube

(4)     5x8x2.5   Ceramic 

(12)    5x11x4   Ceramic 

(3)      6x13x5   Ceramic 

(6)      8x16x5   Ceramic 

(4)      12x18x4   Ceramic 

(2)      12x21x5   Ceramic 

(4)     12x18x4   Ceramic

NOTE: PHOTOS ARE FOR IDENTIFICATION ONLY
Photos are for Seal / Shield / Bearing Style identification only and ARE NOT a photo of the exact bearing being ordered. Please reference the size.

Includes:
1 x SpeedTek RC Stainless Steel Hybrid Shielded Ceramic Bearing Kit for the E-Revo 2.0

SpeedTek RC Stainless Steel Hybrid Shielded Ceramic Bearing Kit for the MST RMX 3.0 KIT & RTR Versions

Features:
Steel, Ceramic Hybrid, Orange Sealed bearings are specially designed for any application seeking a high precision, free spinning bearing. These are the true secret weapon for serious rc racers and long distance casters. ABEC 7 tolerances makes the Orange Seal line the closest precision tolerance that SpeedTek RC has to offer. The removable, non-contact rubber seals results in a bearing with less drag and that requires less maintenance than a typical shielded bearing. The Grade 5 ceramic Si3N4 balls will allow the bearing to be lighter and spin 50% faster than a traditional steel bearing. LD = Lube Dry Bearings have been clean and are free of all grease and Oils.

Specifications:
Bearing Material: Stainless Steel 440C, Ball Material: Ceramic SI3N4, ABEC#7/ISOP4
Enclosure: Two Seals, Enclosure Material: Rubber Seal
Retainer Material: Stainless Steel, Radial Play: C0, Lubrication: LD Dry Lube
(4)     3x6x2.5   Ceramic
(1)     4x10x4   Ceramic
(8)     5x8x2.5   Ceramic
(1)     5x10x4   Ceramic
(2)     5x11x4   Ceramic
(2)     8x12x3.5   Ceramic
(4)     10x15x4   Ceramic

NOTE: PHOTOS ARE FOR IDENTIFICATION ONLY
Photos are for Seal / Shield / Bearing Style identification only and ARE NOT a photo of the exact bearing being ordered. Please reference the size.

Includes:
1 x SpeedTek RC Stainless Steel Hybrid Shielded CeramicBearing Kit for the MST RMX 2.0 KIT & RTR Versions

SpeedTek RC Stainless Steel Hybrid Shielded Ceramic Bearing Kit for the MST RMX 2.5 S KIT & RTR Versions

Features:
Steel, Ceramic Hybrid, Orange Sealed bearings are specially designed for any application seeking a high precision, free spinning bearing. These are the true secret weapon for serious rc racers and long distance casters. ABEC 7 tolerances makes the Orange Seal line the closest precision tolerance that SpeedTek RC has to offer. The removable, non-contact rubber seals results in a bearing with less drag and that requires less maintenance than a typical shielded bearing. The Grade 5 ceramic Si3N4 balls will allow the bearing to be lighter and spin 50% faster than a traditional steel bearing. LD = Lube Dry Bearings have been clean and are free of all grease and Oils.

Specifications:
Bearing Material: Stainless Steel 440C, Ball Material: Ceramic SI3N4, ABEC#7/ISOP4
Enclosure: Two Seals, Enclosure Material: Rubber Seal
Retainer Material: Stainless Steel, Radial Play: C0, Lubrication: LD Dry Lube
(4)     3x6x2.5   Ceramic
(1)     4x10x4   Ceramic
(8)     5x8x2.5   Ceramic
(1)     5x10x4   Ceramic
(2)     5x11x4   Ceramic
(2)     8x12x3.5   Ceramic
(4)     10x15x4   Ceramic

NOTE: PHOTOS ARE FOR IDENTIFICATION ONLY
Photos are for Seal / Shield / Bearing Style identification only and ARE NOT a photo of the exact bearing being ordered. Please reference the size.

Includes:
1 x SpeedTek RC Stainless Steel Hybrid Shielded CeramicBearing Kit for the MST RMX 2.0 KIT & RTR Versions

SpeedTek RC Stainless Steel Hybrid Shielded Ceramic Bearing Kit for the MST RMX 2.5 RS KIT & RTR Versions

Features:
Steel, Ceramic Hybrid, Orange Sealed bearings are specially designed for any application seeking a high precision, free spinning bearing. These are the true secret weapon for serious rc racers and long distance casters. ABEC 7 tolerances makes the Orange Seal line the closest precision tolerance that SpeedTek RC has to offer. The removable, non-contact rubber seals results in a bearing with less drag and that requires less maintenance than a typical shielded bearing. The Grade 5 ceramic Si3N4 balls will allow the bearing to be lighter and spin 50% faster than a traditional steel bearing. LD = Lube Dry Bearings have been clean and are free of all grease and Oils.

Specifications:
Bearing Material: Stainless Steel 440C, Ball Material: Ceramic SI3N4, ABEC#7/ISOP4
Enclosure: Two Seals, Enclosure Material: Rubber Seal
Retainer Material: Stainless Steel, Radial Play: C0, Lubrication: LD Dry Lube
(4)     3x6x2.5   Ceramic
(1)     4x10x4   Ceramic
(8)     5x8x2.5   Ceramic
(1)     5x10x4   Ceramic
(2)     5x11x4   Ceramic
(2)     8x12x3.5   Ceramic
(4)     10x15x4   Ceramic

NOTE: PHOTOS ARE FOR IDENTIFICATION ONLY
Photos are for Seal / Shield / Bearing Style identification only and ARE NOT a photo of the exact bearing being ordered. Please reference the size.

Includes:
1 x SpeedTek RC Stainless Steel Hybrid Shielded CeramicBearing Kit for the MST RMX 2.0 KIT & RTR Versions

SpeedTek RC RC Body Lexan Paint Spray Gun

Shake the model spray can evenly first, and leave it to stand for 1~2 minutes to avoid air bubbles when spraying out the paint. Insert the can trigger holder and start spraying.

It is a practical tool for spraying large-sized models with water-coated clay spray cans or car model shell colour paint spray cans to save energy.

It can be used for model paint spray cans such as KORSHI, TAMIYA & MANY MORE!

Specifications:

Material: Plastic

Weight: 32g

NOTE:  Does not include spray paint

Includes:
1 x SpeedTek RC RC Body Lexan Paint Spray Gun

SpeedTek RC Precision Masking Tape (3mm x 50M)

Features:

-Ideal for painting work in the field of plastic or RC model making

-1 roll of 50 m masking strips

-Prevents the colour from running out

-PET plastic covers keep the thin rollers in shape and protect against dirt

Includes:
1 x SpeedTek RC Precision Masking Tape (3mm x 50M)